Impact Factor: 1.035
ISSN Print: 1091-028X
INSTRUCTIONS FOR AUTHORS
Journal of Porous Media
THE Journal of Porous Media welcomes original, full-length research manuscripts and technical notes in a variety of research areas that present novel findings pertinent to the study of porous media. Only manuscripts that have not been previously published and are not under consideration for publication elsewhere may be submitted. Letters to the Editor will be considered, subject to approval of the Editor-in-Chief.
SUBMISSION FOR PEER REVIEW
GENERAL INSTRUCTIONS: Articles should be submitted through the Begell House Online Submission Program by registering on the website (http://submission.begellhouse.com).
SUBMISSION INSTRUCTIONS: If you are a first-time user of our Submission Program, please click on the New User icon located at the top of the Submission home page. Please complete the registration form and then click on the Submit button on the bottom left side of the form. Your completed form will be reviewed and a registration confirmation will be emailed to you within 24 hours. Please make sure you keep your username and password available for further use on the submission site. Although you will have the option to change your password you should never register again on the submission site.
If you have previously completed a registration form please select Journals from the list of products, enter your username and password and click on the Login button.
SUBMISSION OF ACCEPTED ARTICLE
After a manuscript has been accepted and all required revisions have been incorporated, e-mail the final manuscript (double-spaced, 12-point type, and 1-inch margins all around) to the Editor-in-Chief at the email address above. A signed Begell House copyright release form must be included with your final manuscript. Please provide the copyright release form in PDF format. Figures should be saved in separate files from text and tables. Please see the section on electronic image preparation for submitting figures correctly and at the highest possible quality. The preferred format for manuscripts is Microsoft Word, with equations created in MathType. Articles will be accepted in LaTex format but final manuscript must include both the LaTex files and a PDF file that includes all revisions made to the original article.
PREPARATION OF MANUSCRIPTS
MANUSCRIPT FORM: Manuscripts must be in English, double-spaced, in 12-point type, on US Letter or A4 paper with ample margins. Number all pages consecutively, and order as follows:
For articles containing more than a few symbols, include a nomenclature list in alphabetical order, with Greek symbols (also in alphabetical order and with a separate heading) following the alphabetical listing.
Complete Instructions for authors are available at http://vafai.engr.ucr.edu. Submission procedures are frequently updated, so check before submitting your manuscript.
FULL-LENGTH ARTICLES: Full-length articles should not exceed 40 manuscript pages, logically divided into sections and subsections as follows. Introduction: A concise assessment of previous work by others and an explanation of how the present work contributes to the field.
Main Body of Article
Conclusion: Concluding remarks should stand alone and contain sufficient information that reference to the main body of the text for more details is not required.
Acknowledgment(s): Give appropriate credit to anyone who contributed to the work substantially but not sufficiently to be listed as a coauthor.
References: See below for details on formatting reference citations and lists.
Appendices, Tables, & Figure Captions. If present, each category should start on separate page. (As mentioned above, figures should be in separate files).
TECHNICAL NOTES: Technical notes, not to exceed 10 manuscript pages, should disclose new, significant data or developments of limited scope and should contain abstract, introduction, and description of results.
TECHNICAL COMMENTS: Technical comments, not to exceed 4 manuscript pages, should relate to findings previously published in the Journal of Porous Media.
NUMERICAL ACCURACY: JPM will accept for publication only those articles reporting 1) numerical solutions of an engineering problem that fully addresses the accuracy of the computed results, and/or 2) experimental results where the accuracy of the data is adequately addressed. All articles must use SI units throughout; English units may be included parenthetically.
ELECTRONIC IMAGE PREPARATION
Prepare figures so that they are no larger then of 6.5 inches wide and 6.5 inches long. Use only Arial and Symbol fonts for text within figures. Acceptable formats for figures are TIFF, JPEG, or EPS files saved from the original application at 300-600 dpi. Because of the loss of resolution, embedding figure files in MS Word is not recommended. The preferred format is TIFF; however, maintaining a clear quality of the figures is most important. Do not use gray rules, only black. If the text is printed over gray backgrounds for any reason, the gray must be at least 50% lighter than the text. If possible, avoid grayscales entirely. In general, for best results, figures must be submitted at the highest possible quality.
AUTHOR PROOFS AND OFFPRINT ORDER IN FORMATION
A proof of the typeset article will be sent to the corresponding author for review and correction of technical information approximately one month before publication. Proofs are sent by email in PDF format; if a fax is needed, please so indicate in a cover letter with the final submitted materials. The usual turnaround time for corrections is 48 hours (not counting weekends). The corresponding author will receive a copy of the printed issue in which their article appears. An order form for additional offprints, copies, and subscriptions will be included with the author proofs and may be returned with author corrections. Please check if coauthors want to order additional offprint's or issues as well.
Cite references in the text using the last name of the author(s) and the year of publication, either as "(Doe and Johnson, 1992)" or "Doe and Johnson (1992)." For more than two authors, use "Doe et al. (1992)."If any references contain identical authors and year of publication, cite in the form "Doe et al. (1992a). Order the reference list alphabetically and for-mat according to the following samples. Incorrectly formatted reference lists will be returned to the author for correction before acceptance.
McKibbin, R. and O'Sullivan, M.J., Heat Transfer in a Layered Porous Medium Heated from Below, J. Fluid Mech., vol. 118, pp. 141-173, 1981.
Nakayama, A., Kuwahara, F., Kawamura, Y., and Koyama, H., Three Dimensional Numerical Simulation of Flow Through a Microscopic Porous Structure, ASME/JSME Thermal Eng. Conf., vol. 3, pp. 313-318, 1995.
Nield, D.A. and Bejan, A., Convection in Porous Media, Springer-Verlag, New York, 1992. Nozad, I., Carbonell, R.G. and Whitaker, S., Heat conduction in multiphase systems I: Theory and Experiment for two-phase systems, Chem. Eng. Sci., vol. 40, pp. 843-855, 1985.
Rees, D.A.S. and Riley, D.S., The Three-Dimensional Stability of Finite-Amplitude Convection in a Layered Porous Medium Heated from Below, J. Fluid Mech., vol. 211, pp. 437-461, 1990.
Impact Factor: 1.035
ISSN Print: 1091-028X